PPK mapping with
centimeter accuracy. Use fewer GCPs
Why camera synchronization is so important
Usually autopilot triggers the camera and records the coordinate it has at that moment. When the drone is flying at 20 m/s and GPS works at 10 Hz, that means your autopilot will have position readings only each 4 m, which is not suitable for precise georeferencing. In addition, there is always a delay between the trigger and the actual moment the photo is taken.
Reach eliminates the delay
Reach solves the problem of positioning by connecting directly to the camera hot shoe port, which is synced with the shutter. The time and coordinates of each photo are logged with a resolution of less than a microsecond. This method allows GCPs to be used only to check your accuracy.
1. Connect Reach to a hot shoe port on a camera
Every time a photo is taken camera produces a pulse on a flash hot-shoe connector which is synced to a shutter opening.
2. Fly a drone, Reach will record photo events
Reach captures flash sync pulses with sub-microsecond resolution and stores them in a raw data RINEX log in the internal memory.
3. Download logs from Reach and base station
After the flight, get the RINEX logs from your airborne Reach module and a base station (Reach RS, CORS or another receiver).
4. Process logs and get a file with geotags of photos
Process RINEX files using free RTKLIB software. The produced file with precise coordinates of the photos can be used for georeferencing.
NTRIP or another Reach as a base station
To calculate centimeter-precise coordinates in PPK and RTK, Reach needs corrections from a base station. It could be either another Reach receiver or an NTRIP service. VRS is also supported.
Reach M2 works seamlessly with other Reach receivers over any link and are compatible with any other receiver that supports RTCM3 and NTRIP.
Reach M2 and Reach RS2
Provides robust performance and quick initialization. Allows working on long baselines.
Up to 60 km
Up to 100 km
Time to fix
RINEX logging update rate
Up to 20 Hz
Comes with an app
ReachView is the most user-friendly software for data collection that is available both for Android and iOS. With ReachView, you can control all the features of Reach receivers, such as setting up a base station, logging RINEX data, configuring NMEA output, and monitoring data.
Reach is able to trigger cameras as well as register events. The event mark feature is a must for aerial mapping as it allows the precise time when the shutter was activated to be registered.
Simple log management
Logs are automatically recorded directly to RINEX in the internal memory. View a list of the logs and download them using the ReachView app.
ReachView shows current satellite levels, your location on a map, and much more
- Dimensions 15.4 x 45.3 x 14.6 mm
- Weight 20 g
- Operating tº -20…+65 ºC
- Input voltage on USB and JST-GH 4.75 – 5.5 V
- Antenna DC bias 3.3 V
- Av. consumption @5V 200 mA
- Static horizontal 4 mm + 0.5 ppm
- Static vertical 8 mm + 1 ppm
- Kinematic horizontal 7 mm + 1 ppm
- Kinematic vertical 14 mm + 1 ppm
- LoRa radio (sold separately)
- Frequency range 868/915 MHz
- Distance Up to 8 km
- Wi-Fi 802.11b/g/n
- Bluetooth 4.0/2.1 EDR
- Ports USB, UART, Event
- Corrections NTRIP, RTCM3
- Position output NMEA, LLH/XYZ
- Data logging RINEX with events with update rate up to 20 Hz
- Internal storage 16 GB
- Signal tracked GPS/QZSS L1C/A, L2CGLONASS L1OF, L2OFBeiDou B1I, B2I Galileo E1-B/C, E5b
- Number of channels 184
- Update rates 10 Hz GNSS
- IMU 9DOF