Worldwide Delivery Available
We’re Here to Help! 01748 905 089
Free UK Delivery on orders over £99*

Mauch 058 - PC-2x15A Ideal Diode / BattShare

Code: Mauch-058
  • £49.30 (inc. VAT)
35 In Stock Now | Usually dispatched within 24 hours
Order within for delivery on Tuesday 20th April
Loading...

The PC – 2x 15A is a two-supply current sharing controller which incorporates MOSFET ideal diodes. The diodes block reverse and shoot-through currents during start-up and fault conditions. Their forward voltage is adjusted to share the load currents between supplies. Unlike other sharing methods, neither a share bus nor trim pins on the supply are required.

The PC – 2x 15A is a two-supply current sharing controller which incorporates MOSFET ideal diodes. The diodes block reverse and shoot-through currents during start-up and fault conditions. Their forward voltage is adjusted to share the load currents between supplies. Unlike other sharing methods, neither a share bus nor trim pins on the supply are required. The dual function of this device makes it possible to integrate it into applications, where either a redundant power supply is required, or a 50/50 current share between 2 power supplies, even if they’re on 2 different main batteries (GND bridge required). The PL - 2x15A can be also used in normal remote controlled applications without Power-Cube and flight controller. For example connect directly 2x 2S LiPo (doesn't matter if different capacity) to the two inputs and the output to the receiver or servo rail. Then you have an redundant power supply, with an total capacity of mAh / LiPo 1 plus mAh / LiPo 2. Scope of delivery:

  • 1x PC - 2x 15A Board
  • 2x Input cable / Molex / Click-Mate / 2.0 / L=200mm,  red/black
  • 4x Output cable / JR Servo connector / L=200mm, red/black
  • 1x Transparent shrinking tube

REM: The cables are delivered separate and need to be soldered onto the board. This allows that the cable length can be adjusted before installation, to match the setup of the system. Setup and Usage The PC – 2x 15A is a two-supply current sharing controller which incorporates MOSFET ideal diodes. The diodes block reverse and shoot-through currents during start-up and fault conditions. Their forward voltage is adjusted to share the load currents between supplies. Unlike other sharing methods, neither a share bus nor trim pins on the supply are required. The dual function of this device makes it possible to integrate it into applications, where either a redundant power supply is required, or a 50/50 current share between 2 power supplies, even if they’re on 2 different main batteries (GND bridge required). The PL - 2x15A can be also used in normal remote controlled applications without Power-Cube and flight controller. For example connect directly 2x 2S LiPo (doesn't matter if different capacity) to the two inputs and the output to the receiver or servo rail. Then you have an redundant power supply, with an total capacity of mAh / LiPo 1 plus mAh / LiPo 2. The input and output have blue LED’s for power good indication. The FET’s have red LED’s to indicate if they are switched off. Battery Share Function: If both input voltages are within +/-3%, then the output current is shared 50/50 from both power supplies. The device need a minimum output current of 0.03A (30mA) to activate the current sharing. If the output current is below that value, but both input voltages are the same, then any input (randomly) will be selected until the output current is high enough and the device start to share the current. Ideal Diode Function: If either input voltage is lower than 3% from the other, then this input is disabled and the full output current gets supplied by the higher input voltage power supply. Specification: Input voltage: 2x 3.3-18.0V / 2x 15A Voltage drop input/output: 0.01V/A -> 10mV/A Main PCB: 31 x 25 x 4mm / 4.2g Input cable: 2x Molex / Click-Mate / 2.0 / L=200mm, in either red/black or white/black. Output cable: 4x JR Servo connector / L=200mm, in either red/black or white black. Weight cable set: 19g https://www.3dxr.co.uk/wp-content/uploads/2018/03/1.jpg INPUT 1 OFF, or below 3.3V. INPUT 2 OFF, or below 3.3V. Output   OFF CURRENT SHARING  OFF https://www.3dxr.co.uk/wp-content/uploads/2018/03/2.jpg INPUT 1 ON INPUT 2 OFF, or below 3.3V. Output   ON CURRENT SHARING  OFF https://www.3dxr.co.uk/wp-content/uploads/2018/03/3-1.jpg INPUT 1 OFF, or below 3.3V. INPUT 2 ON Output   ON CURRENT SHARING  OFF https://www.3dxr.co.uk/wp-content/uploads/2018/03/4.jpg INPUT 1 ON INPUT 2 ON -> Input voltage 2 is 3% lower than input 1, or output current is below 0.03A Output   ON CURRENT SHARING  OFF https://www.3dxr.co.uk/wp-content/uploads/2018/03/5.jpg INPUT 1 ON -> Input voltage 1 is 3% lower than input 2, or output current is below 0.03A INPUT 2 ON Output   ON CURRENT SHARING  OFF https://www.3dxr.co.uk/wp-content/uploads/2018/03/6.jpg INPUT 1 ON INPUT 2 ON Output   ON CURRENT SHARING  ON  -> Input 1 and 2 are within +/-3% Redundant power supply setup with 2x Power-Cube 3 and 2 LiPo's: https://www.3dxr.co.uk/wp-content/uploads/2018/03/PC-2x15-pic.png

Free UK standard delivery for orders over £99*. (excludes certain items such as batteries) 

Next Day delivery available with DHL Express to the UK, USA and most of Europe available

Saturday Delivery Available in the UK

For full details on our delivery services click here

Be the first to review Mauch 058 - PC-2x15A Ideal Diode / BattShare. Write a review
Contact us with any questions you have about this product
Top